Got it — here's the write-up as a standard instructions post, not the ingredients format.
FunPX Foam RC Airplane Drone — Setup & Operation Instructions
Contents
Drone
Drone Controller
Replacement Propellers
Module Battery & Type-C USB Charging Cable
How to Replace Propeller
Grasp the bottom of the motor base, pull out the damaged fan blade with strength, and replace it with a new one. Pay attention to distinguish A and B blades.
There is a letter on each blade — match the blade with the corresponding letter on the drone.
Charging/Battery
Please turn off the drone before charging.
Connect the battery charger to the charging port of the drone.
Connect the charging cable to a power source.
Note: The USB charging cable will light up when the battery is charging, and it will turn off when the battery is full. The charging time is about 50 minutes.
Remote Control
Open the battery cover and install 3 x 1.5V "AA" batteries, as shown in the figure.
Rechargeable Battery Warning (Replaceable Battery)There is a risk of fire and personal injury if the battery is punctured, damaged, or misused.
Do not disassemble, crush, burn, or use short-circuit batteries
Do not expose the battery to extreme temperature or humidity
Keep away from flammable materials and direct sunlight
Only use the charger, wire, or adapter provided
Only adults should charge the battery
Adult supervision is required when charging
Allow the battery to cool to the proper temperature before charging
Please stop charging if the battery gets hot, expands, smokes, or gives off a strong smell
Charge on nonflammable materials and keep away from flammable materials
Battery chargers, power cords, plugs, enclosures, and other components used with this product should be checked regularly and observed for damage
Remove the battery before storage (if removable)
Recycle or dispose of batteries according to local laws
The battery or battery pack should not be disassembled, crushed, punctured, opened, or otherwise destroyed
If the battery is swallowed, seek medical advice immediately
If the electrolyte comes into contact with skin or eyes, rinse immediately with fresh water for at least 15 minutes and seek medical advice immediately
Store batteries in their original packaging and keep away from metal objects that could short circuit them
Do not drop the battery or subject it to strong mechanical impact
During use and storage, keep the battery or battery pack clean and dry. If the metal terminal is dirty, please wipe it with a soft dry cloth
Charge the battery or battery pack before use
It may be necessary to charge and discharge the battery or battery pack twice or three times to obtain the best performance when it is used for the first time or stored for a long time
It is better to charge the battery or battery pack at 15°C to 30°C unless otherwise specified by the manufacturer
Keep original product information for future reference
Battery WarningDo not mix old and new batteries
Do not mix alkaline batteries, standard batteries (carbon zinc batteries), or rechargeable batteries
Alkaline batteries are recommended (only batteries of specified voltage are used)
Insert the battery with the correct polarity; be sure to use it under the supervision of an adult, and replace the battery and charge it (if applicable)
Do not try to charge a non-rechargeable battery
Do not short circuit the battery supply terminal
Do not handle the battery in fire — the battery may explode or leak
Remove the battery before storage
Recycle or dispose of batteries according to local laws
Please keep these instructions for future reference
Overview
Diagram callouts: A1 / A2 / B1 / B2 (propeller positions), ON/OFF switch, Module battery.
Remote control labels: Speed control, Throttle/Steering lever, Turn left fine-tuning, Turn right fine-tuning, Headless mode, Power switch, One key takeoff/Landing, Light control, Forward fine-tuning, Backward fine-tuning, Flip, Forward/Backward/Sideflight lever, Right side fine-tuning, Left side fine-tuning, Short press for one key correction / Long press for emergency stop.
Drone Operation Guide
1. Pre-Flight Inspection
Read all the warnings and instructions.
Install batteries in the drone and remote control.
Make sure the drone and remote control are powered off.
Charge the battery.
2. Select Location
Keep at least 5 feet of clearance around the drone and 10 feet from bystanders. Before retrieving or picking up the drone, be sure to turn off the remote control to avoid starting the propeller accidentally.
3. Pairing the Drone
Make sure the remote control is off.
Put the drone on flat ground.
Turn on the drone switch first, then turn on the remote control switch — the drone will synchronize automatically.
The drone's light will flicker during the pairing process and remain on after pairing is complete.
Calibrate the aircraft (calibrate when the aircraft is unstable or flying erratically): With the remote control on and the drone flat on the ground, press the "One Key Correction" button before takeoff. Once the drone's light changes from flashing to solid, calibration is complete.
Gliding Take Off
Push the throttle to the maximum — the drone will glide and take off in about 2 seconds.
Note: Glide take-off should be carried out on smooth, windless ground.
Throwing Function
After the drone's frequency alignment is complete, pick up the drone and throw it out level (parallel to the ground) — the drone will hover in mid-air.
One Key Take Off & Landing
Press the "Takeoff/Landing" button to trigger automatic take-off and landing.
Operation Introduction
Hover up and down
Turn left / right
Forward and backward
Lateral movement — push right to send the drone away from you, push left to move it toward you, and so on.
Auto Orientation
When the drone is in auto orientation mode, it will orient to the user (remote control) no matter which direction the drone is facing.
Press the "Headless Mode" button — the fuselage light will enter a slow flashing state, indicating the drone is in automatic positioning mode. Press the "Headless Mode" button again to exit this mode.
Tips
Do not crash the drone into sand or dirt — the gears may become clogged.
When learning to fly for the first time, practice taking off and spinning.
Keep several feet away from walls and buildings.
Always press the throttle lever all the way after a crash or if something gets stuck in the propellers.
Do not fly the drone above or near people — sudden wind changes or other conditions may cause an accidental crash.
Fly responsibly, abide by relevant laws, and respect the privacy and property rights of others.
The drone should never be modified or used for anything except its intended purpose.
WARNING: Without the explicit approval of the responsible party, changes or modifications to the device may cause the user to lose the authority to operate the equipment.
Troubleshooting
When the remote control switch is turned on, the remote control lamp does not light:
Check that the battery in the remote control is installed correctly.
Replace the battery with a new one.
The remote control power indicator flashes during flight:
The remote battery is low — land the drone immediately.
Replace the old battery.
The drone and remote control are paired correctly, but the drone cannot take off:
The drone battery needs to be charged — use the USB charging cable to connect the drone battery to a power source.
After fine-tuning the drone, the flight is very unstable and unable to fly normally:
One or more blades may be damaged. Please replace the appropriate blades and try again.
Press the remote control lever toward the inner side of the remote control for 5 seconds — the remote control will beep twice, and the gyroscope will reset.
Turn off the drone and remote control, then re-pair the drone.
Remote control and drone cannot be paired:
The remote control must be within 12 feet of the drone. Note: If there are multiple unpaired drones within 12 feet, one must be successfully paired before other drones can be paired.